Gator Sealers and Resealers

Nitterhouse Masonry Products stocks a wide range of Alliance Gator sealers and resealers to help you complete any project. Browse our inventory of Gator products, including Gator Sealant Wet Look Finish, Gator Sealant Satin Look Finish, Gator Sealant Natural Look Finish, Gator Resealer and Gator Hybrid Seal.

To learn more about our Gator supplies and masonry products, reach out to our team online. You can also find Alliance Gator products in-store.

1. Gator Sealant Wet Look Finish

Product Description

Gator Sealant Wet Look Finish bores deep into natural stone pores and concrete pavers, reducing the dirt and oil penetration. 

The Gator product helps impede corrosion from:

  • Motor oil and grease stains.
  • De-icing salt.
  • Ultraviolet rays.

Product Features 

Gator Sealant Wet Look Finish features include:

  • Easy to maintain and clean
  • Solvent-based
  • Non-slip formula
  • High-gloss, lustrous finish
  • Ensures colors look more vibrant

Product Applications 

This product is intended for use on dry cast concrete pavers.

Product Instructions 

Follow these steps for best results when using Gator Seal Wet Look Sealer:

  1. Test Gator Sealant on a small concealed area of approximately 4 square feet to ensure the results will meet your expectations.
  2. Use Gator Clean products to remove all stains from the concrete pavers. To remove any unknown coating that remains on the concrete paver surface, use Gator Clean Sealer Stripper. 
  3. Clear away any contaminated jointing material and replace it with Gator Polymeric Sand. Follow the directions on the back of the package for proper sand installation. 
  4. To ensure the Gator Polymeric Sand properly hardens, wait at least 48 hours at a minimum temperature of 60 degrees Fahrenheit. It’s also critical that no rainfall occurs during this time.
  5. Use Gator Efflorescence Cleaner to clean the entire surface. Doing so will completely clean the surface for appropriate sealer adhesion and remove the efflorescence trapped in the concrete paver pores.
  6. Just like you did when applying the Gator Polymeric Sand, wait at least 48 hours at a minimum temperature of 60 degrees Fahrenheit. Again, plan to complete this process when there is no chance of rain so that the concrete paver surface and sand remain dry.
  7. Use a sprayer in 60 square foot sections to apply one coat of Gator Seal Wet Look Sealer. Next, use a solvent-resistant foam roller to extricate excess sealer left on the surface. Gator Seal Wet Look Sealer is rain safe and water-repellent after 90 minutes.
  8. Before using the sealed area, let the sealer dry for 24 hours. 

Please Note 

Please take note of the following considerations before you use the product:

  • Only seal concrete pavers 60 days after their installation date, and always make sure to consult with the team at Nitterhouse Masonry Products for recommendations. 
  • Ensure jointing sand and concrete pavers are 100% dry.
  • When the sealer is applied, the temperature should be between 60 degrees Fahrenheit and 85 degrees Fahrenheit and the concrete paver surface must be cool to the touch.
  • Remove all rust stains, oil and grease from concrete pavers by cleaning them with Gator Clean products.
  • Remove any trapped efflorescence with Gator Efflorescence Cleaner. This product will also help to ensure a proper sealer adhesion — use just one layer of sealer.
  • Make sure you will have at least 48 hours of dry conditions before applying Gator Seal Wet Look Sealer. 
  • This product cannot be employed as a resealer, as it’s explicitly formulated for use on unsealed surfaces.
  • Wear respiratory protection, eye protection and protective gloves. 

2. Gator Sealant Satin Look Finish

Product Description

Gator Sealant Satin Look Finish bores deeply into natural stone pores and the natural concrete pavers, thus reducing the dirt and oil penetration. 

Gator Sealant for Natural Stones and Concrete Pavers Satin Finish helps protect concrete pavers and natural stones from corrosion that can result from:

  • Motor oil and grease stains.
  • De-icing salt.
  • Ultraviolet rays.

Product Features 

Features of this product include:

  • Easy to maintain and clean
  • Solvent-based
  • Low Gloss
  • Non-slip formula
  • Ensures colors look more vibrant

Product Applications 

Gator Sealant Satin Look Finish is designed for use on dry cast concrete pavers. It is specifically formulated to be used on unsealed surfaces.

Product Instructions 

See eight-step instructions and accompanying notes for Gator Seal Wet Look Sealer product for proper use. 

3. Gator Sealant Natural Look Finish

Product Description

Gator sealant for masonry, walls, concrete and clay pavers and natural stones is composed of fluorochemical polymers. This Alliance Gator sealer passes through the pores of the natural stones or concrete as well as walls and masonry.

Gator Sealant Natural Look Finish helps hinder:

  • Grease and motor oil stains.
  • Stains for up to 10 years.
  • Corrosion from de-icing salt.
  • Effects of ultraviolet rays.

Product Features 

This product is:

  • A non-slip formula.
  • Easy to maintain and clean.
  • Non-film-forming.
  • Applicable on damp surfaces.

Product Applications 

This sealer is designed for use on:

  • Masonry.
  • Retaining walls.
  • Natural Stones.
  • Clays pavers.
  • Concrete pavers.

Product Instructions 

Follow these nine steps for best results when using Gator Sealant Natural Look Finish:

  1. Test Gator Sealant on a small concealed area of approximately 4 square feet to ensure the results will meet your expectations.
  2. Use Gator Clean products to remove all stains from the concrete pavers. To remove any unknown coating that remains on the concrete paver surface, use Gator Clean Sealer Stripper. 
  3. Clear away any contaminated jointing material and replace with Gator Polymeric Sand. Follow directions on the back of the packages for proper sand installation. 
  4. To ensure the Gator Polymeric Sand properly hardens, wait at least 48 hours at a minimum temperature of 32 degrees Fahrenheit. It’s also important that no rainfall occurs during this time, so plan accordingly.
  5. Use Gator Efflorescence Cleaner to clean the entire surface. Doing so will intensely clean the surface for appropriate sealer adhesion and remove the efflorescence trapped in the concrete paver pores.
  6. Again, wait at least 48 hours at a minimum temperature of 32 degrees Fahrenheit. Just as with the Gator Polymeric Sand, it’s critical that no rainfall occurs during this time so that the concrete paver surface and sand remain dry.
  7. For the best results, use a sprayer in 60 square foot sections to apply one coat of Signature Series Natural Look Sealer. Next, use a solvent-resistant foam roller to extricate excess sealer left on the surface. Signature Series Natural Look Sealer is rain safe and water-repellent after 90 minutes.
  8. Before using the sealed area, let the sealer dry for 24 hours. 

Please Note 

Please take note of the following considerations before installing the product:

  • Only seal concrete pavers 60 days after their installation date, and always make sure to consult with the team at Nitterhouse Masonry Products for recommendations. 
  • Ensure jointing sand and concrete pavers are completely dry.
  • When the sealer is applied, the temperature should be between 32 degrees Fahrenheit and 85 degrees Fahrenheit. The concrete paver surface must be cool to the touch.
  • Remove all rust stains, oil and grease from concrete pavers by cleaning them with Gator Clean products.
  • Remove any trapped efflorescence with Gator Efflorescence Cleaner. This product will also help to ensure a proper sealer adhesion. Use just one layer of sealer.
  • You can apply Natural Look Sealer on damp or dry surfaces. This product cannot be employed as a resealer as it’s explicitly formulated for use on unsealed surfaces only. 
  • Wear respiratory protection, eye protection and protective gloves. 

4. Gator Resealer

Product Description

Gator Resealer sinks into the existing sealer and forms a new protection surface, thus reducing the dirt and oil penetration. 

Benefits of this product include the following:

  • Helps prevent corrosion from de-icing salt
  • Protects against grease and motor oil stains
  • Helps protect against ultraviolet rays effects

Product Features 

Features and abilities of Gator Resealer include:

  • Non-slip formula
  • Revives look
  • Easy to maintain and clean 
  • Solvent-based
  • Ensures color vibrancy
  • Can be applied to Gator Satin and Wet look finishes

Product Applications 

Gator Resealer is designed for use on dry cast concrete pavers. 

Product Instructions 

Follow these six steps for best results when using Gator Resealer:

  1. Test Gator Sealant on a small concealed area of approximately 4 square feet to ensure the results will meet your expectations.
  2. Ensure there is no rain forecasted for the next 24 hours before commencing the project.
  3. Use Gator Clean products to remove all rust stains, grease and oil from the concrete pavers. To completely clean the surface of concrete pavers and ensure correct Gator Seal Resealer adhesion, use Gator Efflorescence Cleaner. 
  4. To ensure the Gator Polymeric Sand and concrete paver surface are dry, wait at least 48 hours at a minimum temperature of 60 degrees Fahrenheit. It’s also critical that no rainfall occurs during this time.
  5. Use a foam roller to apply coat of Gator Seal Resealer. Gator Resealer is rain safe and water-repellent after 90 minutes.
  6. Before using the sealed area, let the resealer dry for 24 hours.

Please Note 

Please take note of the following considerations before installing the product:

  • Only seal concrete pavers 60 days after their installation date, and always make sure to consult with the team at Nitterhouse Masonry Products for recommendations. 
  • Ensure jointing sand and concrete pavers are 100% dry.
  • When the sealer is applied, the temperature should be between 60 degrees Fahrenheit and 85 degrees Fahrenheit. The concrete paver surface must be cool to the touch.
  • Remove any ground-in dirt from the concrete paver’s surface with Gator Efflorescence Cleaner. Using Gator Efflorescence Cleaner before a Resealer will ensure deeper penetration into the cleaned surface. Use just one layer of sealer.
  • Make sure you will have at least 48 hours of dry conditions before applying Gator Seal Resealer. 
  • Wear respiratory protection, eye protection and protective gloves. 

5. Gator Hybrid Seal

Product Description

Use Gator Hybrid Seal — a product made of 100% pure high-grade acrylic — to seal natural stones and pavers. This product passes through natural stone pores and the concrete paver, reducing the dirt and oil penetration. One gallon of the sealer will cover roughly 100 square feet. Coverage will vary depending on the porosity of the surface of the stones and joint size.

Gator Hybrid Seal helps to prevent:

  • Grease and motor oil stains.
  • Ultraviolet rays.
  • Corrosion from de-icing salt.

Product Features 

Features of Gator Hybrid Seal include:

  • Rapid Installation
  • Will not discolor
  • Works above 40 degrees Fahrenheit or 5 degrees Celsius 

Product Applications 

This product is designed for use on clay pavers.

We recommend a test area if using sand consisting of a polymer as jointing material. Some clay pavers retain humidity and are more permeable, which might cause the polymers to react on the damp surface and cause a haze.

Product Instructions

Whether you are using Zero Gloss, Low Gloss or High Gloss Gator Hybrid Seal, follow these steps:

  1. If using this product as a stand-alone sealer, apply Gator Hybrid Seal at the rate of 200 square feet per gallon. If needed, spray on the surface and back roll to even out the surface. 
  2. You can also use Gator Hybrid Seal as a Sealer or Joint Sand Stabilizer. Apply at the rate of 100 square feet per gallon. Then, using a roller or squeegee, force the excess sealer from the surface into the joints.
  3. Concrete pavers should only be sealed 60 days after their installation date. Seek advice from the concrete paver manufacturer for their recommendation. 
  4. To ensure results will meet your expectations, always test the product on a small concealed area of approximately 4 square feet.
  5. Use the Gator Clean Efflorescence Cleaner to clean the surface. This product will effectively clean the surface for desired sealer adhesion and remove the efflorescence trapped in the concrete paver pores. 
  6. Hold off on applying Gator Hybrid Seal if rain is expected within 24 hours.
  7. Do not allow the sealer to puddle. 
  8. When the sealer is applied, the temperature should be between 40 degrees Fahrenheit and 85 degrees Fahrenheit. The concrete paver surface must be cool to the touch.
  9. This product is rain safe and water-repellent after 24 hours, so you should allow the sealer to dry for 24 hours before using the area.

Please Note 

Please take note of the following considerations before installing the product:

  • Only seal concrete pavers 60 days after their installation date, and always make sure to consult with the team at Nitterhouse Masonry Products for recommendations. 
  • To ensure results will meet your expectations, always test the product on a small concealed area of about 4 square feet.
  • Use Gator Efflorescence Cleaner to clean the surface of the area and remove the efflorescence trapped in the concrete paver pores. 
  • If rain is expected within 24 hours, do not apply.
  • Make sure the sealer does not puddle.
  • Wear eye protection, protective gloves and respiratory protection.

Contact Nitterhouse Masonry for Gator Sealers and Resealers 

To learn more about the Alliance Gator sealers and resealers we sell, call us at 717-267-4500 or contact a representative online. You can also visit us in-store at our Chambersburg location to pick up supplies today. 

Request Details

Thank you for your interest in a Nitterhouse Masonry Product! Please fill out the form below to reach a masonry specialist and we’ll get back to you as soon as possible. We look forward to working with you!